Injection Molded Plastic

The company not only runs the plastic parts on custom automotive plastic injection molding machines, they manufacture the tooling for these operations as well, and are able to provide automotive connector molding for many of their clients. This allows the company to provide very competitive pricing on large plastic parts manufactured in China for distribution anywhere in the world. The company is capable of producing custom automotive plastic injection molding products in all types of engineering grade resins requiring close-tolerance specifications with superior quality and aesthetics. They carry various CAD software programs to ensure we can assist you using most of today's programs.

The wonderful thing about plastic injection molding is the low cost of the parts being produced when you need a large volume of parts. The downside is the cost of injection molding tooling. The toolings, or the molds, range in price anywhere from $2000 for a simple one, to over a hundred thousand dollars for a big and complex injection mold. The way the injection molders figured out how much to charge per part was to weigh the part complete with runner to determine how much plastic resin is used for each part. The size of the part determines what size injection molding machine must be used, and how big the mold is etc.

Approximately 30% of all plastic products are produced using an injection molding process. Of this 30%, a large amount of these products are produced by using custom injection molding technology. Six steps are involved in the injection molding process, after the prototype has been made and approved. The first step to the injection molding process is the clamping of the mold. This clamping unit is one of three standard parts of the injection machine. They are the mold, the clamping unit and the injection unit. The clamp is what actually holds the mold while the melted plastic is being injected, the mold is held under pressure while the injected plastic is cooling. Next is the actual injection of the melted plastic. The plastic usually begins this process as pellets that are put into a large hopper. The pellets are then fed to a cylinder; here they are heated until they become molten plastic that is easily forced into the mold. The plastic stays in the mold, where it is being clamped under pressure until it cools. The next couple of steps consist of the dwelling phase, which is basically making sure that all of the cavities of the mold are filled with the melted plastic. After the dwelling phase, the cooling process begins and continues until the plastic becomes solid inside the form. Finally, the mold is opened and the newly formed plastic part is ejected from its mold. The part is cleaned of any extra plastic from the mold.

For homeowners who do not need a specific design recreated or reproduced, pre-made products are generally a far more cost-effective way to take advantage of plastic injection molding technology. Many companies offer a wide range of pre-made products made from plastic injection molding and chances are, you already own many of these products. One of the most common uses of the procedure for home building and design products is in making trim, ceiling medallions, crown moldings and similar decorative products. These products are often more durable, lightweight, and easier to install than wood, plaster, or other more traditional materials, yet can be stained or painted to have the same classic look. This is but one of the many possibilities for the versatile technology of plastic injections molding.

The 2-shot injection molding process creates the first plastic component, and the material molded round it, using a single mold and a 2-shot injection molding machine. 2-shot machines have two-barrels (one for each material) and they have the ability to rotate the mold. The machine injects the first shot material into cavities on one side of the mold, rotates the mold 180 degrees, and then injects the second shot material onto the first shot. The first and second shots occur at the same time. When the mold opens, it ejects the completed parts from the second shot cavities and it rotates the mold to position the first shot for the second shot. This is accomplished in a machine running in an automatic cycle. Because the 2-shot injection molding process is fast and highly repeatable, the shrinkage of the first shot is very consistent and two materials can be molded together with virtually no flash. 2-shot molding is the process of choice when molded-in graphics or other fine details are required. The elimination of the shrinkage variable allows 2-shot molding to produce details impossible to achieve with over-mold injection molding.